The X-Line Advance FIR-Drive speaker settings library includes settings for the X1-212/90, X1-212/120, X2-212/90, and X2-212/120 models for use in a variety of modes, with the selection of speaker settings guided by LAPS3. Please refer to the Drive Report in LAPS3 to choose the correct mode for your application. Speaker settings for X1 models are included with IRIS Net, while speaker settings for X2 models are available by request.

The X1-212/90 and X1-212/120 version 2.0 speaker settings are time-aligned to allow multi-pattern array creation, with the restriction that only one amplification mode can be used within a single array (either biamp or passive). Do not mix biamp and passive within the same array, and do not mix X2 and X1 models within the same array. Speaker settings for the X1 models are supported in the following Electro-Voice and Dynacord FIR-Drive loudspeaker controllers: RCM modules for EV Tour Grade / Dynacord PowerH series amplifiers, EV Dx46 / Dynacord DSP 600, EV NetMax N8000 / Dynacord P64, Dynacord L & C series amplifiers, Dynacord IPX / TGX series amplifiers.

The X2-212/90 and X2-212/120 version 2.0 speaker settings are also time-aligned to allow multi-pattern array creation. Do not mix X1 and X2 models within the same array. Speaker settings for the X2 models are supported only in the RCM-28 module in combination with the TG7 Tour Grade amplifier, in in specific configurations of the Dynacord IPX / TGX amplifiers. 

The X12-128 version 2.0 speaker settings are time-aligned to be positioned directly underneath an X-Line Advance series array or underneath other Electro-Voice touring, concert, or install line array models utilizing FIR-Drive processing and an 80Hz high pass filter, such as X-Line and X-Line Compact (XLC / XLCi).
The X12-128 subwoofer level and equalization is set for a 1/2 ratio of subs to X1-212 or X2-212. Subwoofer output level and alignment delay may need to be adjusted for your application.
Speaker settings for the X12-128 is supported in the following Electro Voice FIR-Drive loudspeaker controllers only in combination with the TG7 Tour Grade amplifier using the RCM-28, RCM-26, Dx46, or NetMax N8000. Specific configurations
of the Dynacord IPX / TGX amplifiers are also supported. 

The X12-125F version 1.0 speaker settings are time aligned to be flown above, beside, or underneath an X-Line Advance series array in a variety of modes and crossover points. The selection of the appropriate speaker setting is guided by LAPS3; please refer to the Drive Report in LAPS3 to choose the correct mode for your application.
When X12-125F is used as an upper-bass element, and additional mode for X12-128 as a sub-bass element at a crossover of 70Hz is possible.
The X12-125F subwoofer level and equalization is set for a 2/3 ratio to X1-212 or X2-212. Subwoofer output level and alignment delay may need to be adjusted for your application.
Settings for the X12-125F located in the common subwoofers directory of the concert speaker settings are available for use with other Electro-Voice touring, concert, or install line array models such as X-Line, X-Line Compact (XLC / XLCi), and X-Line Very Compact (XLD / XLE).
Speaker settings for the X12-125F models are supported only in the Electro-Voice TG-7 with RCM-28 module, and in specific configurations of the Dynacord IPX / TGX amplifiers.

If you have questions or comments about the presets, please contact the EV Technical Support group within your region. Contact information for support in your region can be found via the Electro Voice website: http://www.electrovoice.com/contact.php